彩钢板建筑漏水解决办法

彩钢板被广泛应用于建筑领域中，彩钢板相比传统的砖、瓦、灰、石为主的结构大优点是施工周期短、建筑物材料轻、基础要求条件低、可以大跨度、室内空间大、使用方便等。但彩钢板也存在有一定的问题，主要问题是：屋盖、铆钉处、板缝处有渗漏现象，影响到正常使用。那么面对彩钢板屋面渗漏应当如何解决呢？
Color steel plate is widely used in the field of architecture, color steel plate compared to the traditional brick and tile, cement and stone structure is the main advantages of short construction period, building materials, light based low requirement, large span, large indoor space, convenient use etc.. But the color plate there are some problems, the main problem is: the roof, rivets, slab joints have leakage phenomenon, affect the normal use. Then, in the face of color steel roof leakage should be how to solve it?
一、铆钉处漏水维修方法：
First, the leakage of rivets repair methods:
济南彩钢板http://www.dafangming.com/应用阳光2000PA单组份防水胶涂刷4次，厚度大约1.5㎜左右，直径Φ60㎜左右，下一次涂刷以上一次涂层不粘手为准，并一次比一次涂的直径大Φ15㎜，呈中间厚圆周薄。
The application of sun 2000PA one component waterproof glue brushing 4 times, the thickness of about 1.5 mm, diameter 60 mm or so, the next time more than a brushing coating non stick hand as the standard, and a large diameter diameter coated 15 mm is thicker in the middle circle thin.
彩钢板
Color steel plate
二、接缝处漏水维修方法：
Two 、 joint leakage maintenance method:
1、小接缝维修方法：
1 、 small seam maintenance method:
①可在缝处两端涂刷宽60㎜阳光2000PA单组份防水胶，缝邻近20㎜不涂。

The in seam width of 60 mm at both ends of brushing the sun 2000PA one component waterproof glue, 20 mm is not coated with the adjacent seam.

②无纺布(或玻璃纤布)，布宽150㎜，粘贴在涂阳光2000PA防水胶上面。
The non-woven fabric (or glass fiber cloth), cloth width of 150 mm, with 2000PA waterproof glue paste in the sun above.
③在无纺布或玻璃纤布上涂刷3遍,涂刷时后一遍比前一遍宽50㎜,厚度1.8㎜左右。后一次涂刷以上一次涂层不粘手为准。
The glass fiber cloth or non-woven fabric brushing 3 times, besmear again after than before over 50 mm wide, 1.8 mm thickness. After brushing the above coating once, non stick hand shall prevail.
岩棉板因其具有较高的强度和保温效果，被广泛应用于外墙保温上。岩棉板使用粘贴方法将保温材料置于建筑物外墙外侧，不占用室内空间，保温效果明显。那么岩棉板的外墙施工粘贴方法有哪些呢？
Rock wool board because of its high strength and insulation effect, is widely used in exterior wall insulation. The rock wool board uses the sticking method to place the heat insulating material outside the outer wall of the building, and does not occupy the indoor space, and the heat preservation effect is obvious. Then, rock wool board external wall construction paste method what?
1、采用点框法，即在岩棉板背面整个周边涂抹适当宽度和厚度的胶粘剂，然后再中间部位均匀涂抹一定数量、一定厚度、直径约为100mm的圆形粘结点，总粘贴面积不小于40%；建筑物在60m及以上时，总粘贴面积不应小于60%。
1, the box method, namely with appropriate width and thickness in the surrounding rock wool board back adhesive, and then the middle part of a certain number of evenly, certain thickness, diameter of circular bonding points 100mm, paste the total area of not less than 40%; the building of 60m and above, the total bonded area should not be less than 60%.
2、配制抹面胶浆，做抹面层级铺贴玻纤网格布。加强型抹面须增设一层网格布，增贴的网格布只能对接，抹面胶浆厚度为3~5mm。普通型抹面层采用单层玻璃纤维网格布，在已贴于墙上的岩棉板面层上抹厚度1~2mm的抹面胶浆，随即将网格布横向铺贴并压入胶浆中；单张网格布长度不宜超过6m，要平整压实，严禁网格布褶皱、不平，搭接长度每侧为100mm
2, preparation of mortar, plastering level do paving fiberglass mesh cloth. Reinforced plaster should be added a layer of mesh cloth, mesh cloth can only increase butt paste, mortar thickness is 3~5mm. Ordinary type plastering the single glass fiber mesh cloth, with the thickness of 1~2mm mortar in the surface layer of rock wool has been affixed to the wall on the horizontal grid cloth will paving and pressing mortar; single mesh length should not exceed 6m, to smooth compaction, forbidden grid cloth folds, uneven, lap length on each side 100mm
3、锚固件固定法，根据设计要求采用机械锚固件辅助固定岩棉板时，应在胶粘剂固化24h后进行；锚固件进墙深度不小于设计（或节点图）要求，锚固件数量级型号根据设计要求确定。
3, anchor fixing method, based on the mechanical auxiliary fixed anchor rock wool board design requirements, should be carried out in curing after 24h; anchor into the wall depth of not less than the design (or graph), the number of anchor level models are determined according to the design requirements.