一、确认位置

1、 Confirm location

设备初始处理后应放置在干净的地面上。根据设备定位，设计图纸定位分区，确定页面尺寸是否与图纸尺寸、设备位置相冲突

The equipment should be placed on a clean ground after initial processing. Based on device positioning, design drawing positioning zones to determine if the page size conflicts with the drawing size and device position

确认场地地面高度，看是否有较大震动，是否需要整平彩钢墙底。

Confirm the ground height of the site to see if there is significant vibration and if it is necessary to level the bottom of the color steel wall.

二、安装要求

2、 Installation requirements

固定外圆弧:与太原彩钢板的连接必须密封，外圆弧柱不连接，圆弧连接点在正确位置，间隙封闭。

Fixed outer arc: The connection with Taiyuan color steel plate must be sealed, the outer arc column is not connected, the arc connection point is in the correct position, and the gap is closed.

用3颗螺钉固定在每个顶板和保护板之间。保护板与立板之间的每个连接处上下均有固定拉杆，施工时固定，且平缝必须垂直

Fix with 3 screws between each top plate and protective plate. Each connection between the protective board and the vertical board is fixed with a tie rod up and down, which is fixed during construction, and the flat joint must be vertical

固定t型吊索:吊索代号沿下拉位置定位，间距不超过1.20m。固定t型梁与太原彩钢板连接时，用角钢或角钢压实，不留下缝隙，实心压在两块彩钢板的连接线上

Fixed T-shaped sling: The sling code is positioned along the downward position, with a spacing not exceeding 1.20m. When fixing the T-beam to connect with Taiyuan color steel plate, angle steel or angle steel should be used to compact without leaving any gaps, and the solid should be pressed on the connecting line of the two color steel plates

固定槽式铝板:槽式铝板固定前，偏差不得超过5mm，槽式铝板用M5x30铝板间接固定，不超过300mm。双绞线必须放置在有槽式铝板的位置，间距不得超过

Fixed slot aluminum plate: Before fixing the slot aluminum plate, the deviation should not exceed 5mm. The slot aluminum plate should be indirectly fixed with M5x30 aluminum plate, not exceeding 300mm. Twisted pair cables must be placed in the position of slotted aluminum plates, with a spacing not exceeding

通风门的安装:通风门的安装应按图纸进行，避免t型房屋。安装及墙面上的回风孔应距地面

Installation of ventilation doors: The installation of ventilation doors should be carried out according to the drawings to avoid T-shaped houses. The installation and return air holes on the wall should be located at a distance from the ground

外观要求:整体安装应平直美观，无冲击和划痕，板线连接平直，板线间距为3-4mm，胶缝应完全平直无缝

Appearance requirements: The overall installation should be straight and aesthetically pleasing, without impact or scratches, with straight board line connections and a spacing of 3-4mm between board lines. The adhesive joints should be completely straight and seamless

门窗的安装位置和开启方向按图纸要求确定。同一太原彩钢板上的单扇门尽量打开，两扇门的中线要尽量与开口连接，以便太原彩钢板切割成门板。连接窗户的结构材料很重要，不能有开口。整个门窗的对接尺寸应均匀右转。

The installation position and opening direction of doors and windows shall be determined according to the drawing requirements. Single doors on the same Taiyuan color steel plate should be opened as much as possible, and the centerline of the two doors should be connected to the opening as much as possible, so that the Taiyuan color steel plate can be cut into door panels. The structural material for connecting windows is very important and there should be no openings. The docking size of the entire door and window should be evenly turned to the right.

感谢您的阅读，此文的文章来源：禹城彩钢厂更多的内容和问题请点击：http://www.lxcaigang.com我们会继续努力的为您提供服务，感谢您的参与.

Thank you for reading. The source of this article is Yucheng Color Steel Factory. For more information and questions, please click: http://www.lxcaigang.com We will continue to work hard to provide you with services. Thank you for your participation